Leading 10 usual forklift crashes ， forklift procedure need to take notice of these issues ！.

Do not undervalue the forklift at the office. If the procedure is bad, there will certainly be significant crashes in minutes, and there are many accidents including forklifts.

Situation 1: The forklift cargo blocked the motorist's sight, and the person in front might not be discovered, leading to a rolling accident.
Case 2: In order to maintain the balance of the forklift when raising hefty items, the staff members utilized their body weight as the weight, which nearly triggered casualties.
Situation 3: The width of the forklift cargo exceeds the allowed size of the path and hangs on the roadside shelf, which almost causes an crash.
Situation 4: Forklift is speeding and rolls over throughout a turn.
Instance 5: The forklift motorist did not observe the pedestrian, and the pedestrian did not discover the forklift.
Case 6: The forklift raises the employees illegally, the forklift driver does not put on the safety belt, the forklift lifter falls and the driver is squashed when the forklift rolls over.
Case 7: The forklift vehicle driver did not use a seat belt and dropped from the automobile when it rolled over and was crushed.
Forklift procedure ought to take note of these issues ：.

Begin.
1. Before beginning, observe the surroundings, and after validating that there are no barriers that hinder the safety and security of driving, beep the horn first and afterwards start.
2. For lorries with hydraulic ( atmospheric pressure) brakes, the brake hydraulic pressure ( atmospheric pressure) gauge need to be safe prior to starting.
3. When the forklift starts with a load, the motorist should initially confirm that the tons is stable and trusted.
4. The begin has to be sluggish and constant.

Driving.
1. When driving, the height in between the bottom end of the fork and the ground should be maintained 300mm-400mm, and the pole ought to be slanted backward. .
2. Do not lift the fork expensive when driving. When going into and leaving the work site or while driving, beware that there will certainly be no obstacles overhead. When the lots is traveling, the fork needs to not be elevated too high, which will certainly influence the stability of the forklift. .
3. After discharging, the fork needs to be lowered to the typical driving placement before driving. .
4. When turning, if there are pedestrians or lorries close by, the driving signal ought to be provided initially. High-speed doglegs are restricted. High-speed sharp turns will certainly create the vehicle to lose lateral security and topple. .
5. When the forklift is downhill, it is purely forbidden to shut off the fire and slide, and it is restricted to brake suddenly while driving with loads unless there are special conditions.
6. When the forklift is running, it has to obey the traffic rules in the factory and should maintain a specific safety and security range from the lorry ahead. .
7. When the forklift is running, the lots must be in the lowest position that does not hinder the driving, and the gantry should be correctly tilted back. The load shall not be raised except when piling or filling. .
8. The elevation of the tons need to not obstruct the chauffeur's sight. In special circumstances, when the item affects the forward vision, drive at a reduced rate when turning around.
9. It is restricted to switch on the ramp, nor to drive across the ramp. .
10. The safe driving rate of the forklift in the manufacturing facility location is 5 km/h, and it needs to drive safely at a low rate when going into the production workshop area. .
11. When the forklift is raised, raised or driven, it is prohibited for personnel to stand on the fork to hold things and play a stabilizing function. .
12. If problems are found, they will certainly be fixed and reported in a timely manner, and they will certainly never ever operate with illnesses or hide them.

packing and discharging.
1. Stand-on Electric Pallet Stacker When fork-loading items, the range between the two forks need to be changed as needed to make the lots of the two forks balanced and not manipulated, and one side of the product ought to protest the rack. .
2. It is forbidden to collaborate with a single fork or use a fork top or draw. In special circumstances, safety and security warning signs must be established to remind bordering pedestrians. .
3. In the process of packing and unloading Electric Forklift Truck for Warehouse products, the forklift should be stopped with the brake. .
4. The speed of the lorry must be slow and consistent. Be careful not to roll the wheels on the dunnage, so as not to extend the rolled objects and harm individuals. .
5. When using a fork to fork the goods, the fork needs to be as deep as possible under the lots, and it should be kept in mind that the fork tip must not touch various other items or things. The load needs to be supported with marginal back tilt of the gantry so that the tons does not glide backwards. The pole can be slanted forward somewhat when the load is reduced to permit easy positioning of the lots and extraction of the forks. .
6. It is prohibited to fork items at high speed and hit tough things with the fork head. .
7. When the forklift is working, it is prohibited for individuals to stand around the fork, so as to stay clear of the collapse of the goods and injure individuals. .
8. Overloading is forbidden, and it is banned to make use of forks to raise workers to take part in high-altitude procedures to avoid high-altitude dropping crashes. .
9. It is not allowed to use the brake inertia to slip, place, round or roll things. .
10. It is not permitted to make use of forks to pick, turn pallet unload.

Leaving .
1. It is forbidden to leave the forklift when the products on the fork are in the air. Before leaving the forklift, you need to discharge the goods or reduced the fork structure.
2. Draw the hand brake take care of to dead or dispirit the hand brake button.
3. The engine is switched off and the power is removed. (Except for unique conditions, such as the vehicle driver does not leave the lorry's view and does not go beyond 1 min).
4. Get rid of the secret. .

Forklift Operation Precautions.
1. Prior to and after the forklift operation, the appearance should be checked, and fuel, lubing oil and air conditioning water must be included.
2. Inspect the safety performance of beginning, running and stopping.
3. Inspect whether the lights and horn signals are total and effective.
4. During the procedure of the forklift, examine whether the pressure and temperature are normal.
5. After the forklift is running, the exterior leak ought to also be checked and the seals need to be changed in time.

Forklift Safety Operation Specifications.
1. You should check prior to leaving the cars and truck;.
2. When you come across somebody in front of you throughout driving, you ought to send a signal at a distance of 5 m;.
3. The driving rate in the factory does not exceed 5 km/h;.
4. When driving, the nadir of the cargo should be 0.3 m ~ 0.4 m in the air;.
5. The turning need to not be as well sharp to prevent the propensity of " totally free turning";.
6. Adding and down the slope needs to be sluggish and consistent, and no switching on the slope is enabled.
7. Do not drive across the slope. When the gradient is more than 10%, the car needs to be driven backwards when going downhill;.
8. When the forklift workers carry the goods and progress, if they encounter big or heavy products and go to the motorist's line of sight, they must take the turning around exercise
.
The "Eight Prohibitions" need to be followed in the procedure.
1. Single fork operation is not permitted.
2. It is not allowed to lift the goods for cross country driving.
3. It is not allowed to grab the goods by turning over the pallet with the fork.
4. It is not enabled to straight shovel chemicals, flammables and other dangerous chemicals with forks.
5. It is not permitted to use inertia force to grab the goods.
6. It is not allowed to use stopping pressure to exile round or easy-to-roll objects.
7. It is not enabled to bring individuals to work on the pallet or fork, and it is strictly prohibited to stand under the fork after the fork is elevated.
8. Do not drive laterally on slopes
.
Car park is not permitted under the following conditions.
1. Curves, slim roadways, train crossings;.
2. Areas with a longitudinal slope higher than 5%.
3. When there is an challenge on one side of the roadway, the contrary side of the area with the very same length as the obstacle ought to be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844